- How are leader lines terminated?
- Do I need a leader with braided line?
- How do I add a leader in Solidworks?
- Will braided line damage my rod?
- What does a hidden line look like?
- Can dimension lines cross?
- What is leader line used for?
- How do you break a leader line in Solidworks?
- What do phantom lines indicate?
- Do I need a leader for pike?
- What should Leader lines never do?
- Can you use fluorocarbon line as a leader?
- How long should a leader be on braided line?
- What are the 8 rules of dimensioning?
- What is a leader or pointer line?
- What are leader lines in Solidworks?
- Should the leader be stronger than the main line?
- Is fluorocarbon leader worth the money?
- Why is braided line Banned?
- What are alphabet lines?
- Can Leader lines be used for notes?
How are leader lines terminated?
Leader Lines A leader line may be terminated in three different ways.
no leaders that are parallel to dimension or extension lines.
no leaders that make a small angle with the surface to which it refers..
Do I need a leader with braided line?
If you are using Braid it’s almost impossible to snap the line, but if you tie on a leader you will be able to break the line right at the knot. Using a light leader will control how much line is broken off at one time.
How do I add a leader in Solidworks?
To add new leaders to an existing annotation:Select the annotation.Press Ctrl and drag an arrowhead handle to a vertex, edge, or face. A new leader is created.
Will braided line damage my rod?
Some folks say braids will cut into rod guides, especially the more inexpensive ones. If you use it you should make sure your rod can handle it. Braids will also bury themselves on the reel spool. To avoid this, spool the line tightly and set the drag light enough so it slips on the hook set.
What does a hidden line look like?
If an edge or surface is blocked from view by another feature, it is drawn using a hidden line. Figures 4-11 and 4-12 show objects that require hidden lines in their orthographic views. … The hidden portion of the line is drawn using a hidden-line pattern, and the visible portion of the line is drawn using a solid line.
Can dimension lines cross?
Dimension lines should not cross, if avoidable. Dimension lines and extension lines should not cross, if avoidable. Extension lines may cross each other. When extension lines cross extension lines or visible lines, no break in either should be made.
What is leader line used for?
There are two main reasons for using leader line. Firstly it can be used to provide increased protection against the sharp edges of teeth, rocks, reef or shell-covered pylons. The other main reason is because some fishing lines are highly visible underwater.
How do you break a leader line in Solidworks?
On the Leaders tab of the respective PropertyManager, under Break Lines:Select Break extension lines to break extension lines around dimension lines and other extension lines.Select Break dimension line to break the dimension line around other dimension lines and other extension lines.
What do phantom lines indicate?
Phantom Line Phantom lines are long-short-short-long lines most often used to show the travel or movement of an object or a part in alternate positions. It can also be used to show adjacent objects or features.
Do I need a leader for pike?
Not only do pike and muskie have a major case of overbite, they can bite through just about any fishing line short of steel wire. … For certain pike and muskie fishing methods, a leader isn’t necessary, and for others it’s almost mandatory.
What should Leader lines never do?
Leaders should never be horizontal or vertical. 28. Leader lines should never cross one another, nor should they be parallel or nearly parallel to nearby dimensions, extension, or cross-hatching lines.
Can you use fluorocarbon line as a leader?
The simple answer is that yes, you can use fluorocarbon line as your leader material and it’s what I use 90% of the time. I prefer using fluorocarbon as my leader material because it’s invisible in the water and is more abrasion-resistant compared to monofilament.
How long should a leader be on braided line?
2 to 4 feetLearn the knot to apply a fluorocarbon or mono leader and gain confidence in it. The technique where I’ve been most pleasantly surprised is when I’m flipping with braid/fluorocarbon. My typical leader length is 2 to 4 feet. Of course, you will need to make some adjustments in your tackle.
What are the 8 rules of dimensioning?
Terms in this set (8)Rule 1: Dimensions should not be duplicated, nor should the same info be given in two different ways.Rule 2: Dimensions should be attached to the view that best shows the contour of the feature being dimensioned.Rule 3: … Rule 4: … Rule 5: … Rule 6: … Rule 7: … Rule 8:
What is a leader or pointer line?
Leader (or pointer) line – Thin continuous line connecting a note or dimension figure with the feature to which it applies. One end of the leader terminates in an arrowhead or dot. The arrowhead touches the outline while the dot is placed within the object or on the outline.
What are leader lines in Solidworks?
You can create leader lines with blocks and notes in 2D panel layouts and harness drawings….Leader LinesText Leaders.Block Leaders.Leader Styles Manager. You use Leader styles to create, delete, edit, and set the current leader.
Should the leader be stronger than the main line?
Leader is usually thicker and stronger than your main line. The length of leader will vary depending on what you’re doing. When throwing lures, you want a shorter leader so it doesn’t impede you from casting far (1-2ft). When using live bait, the decision is up to you.
Is fluorocarbon leader worth the money?
Most anglers would agree that it’s worth the extra cost of fluorocarbon line when it can make the difference between actually catching and simply fishing.
Why is braided line Banned?
Regrettably for the disabled, braided lines are being banned at some fisheries and club waters because of their misuse by some anglers. … This would give the disabled angler (some of whom can’t use mono or flourocarbon lines at all) a chance to fish.
What are alphabet lines?
The Alphabet of Lines is a list of line symbols that engineers use in technical drawings to communicate specific shapes, sizes or surfaces. In the Alphabet of Lines, thick, dark lines represent the outline of an object, showing its visible surfaces and edges.
Can Leader lines be used for notes?
After adding a text note to a drawing, you can add one or more leader lines to the note, using straight or arc leaders.